eve Conference Variant Block
|
Day 1 Mar.12th(Thu） |
||
|
A.M. |
Keynote Speech |
|
|
09:00 |
Welcome Speechby Ringier |
|
|
09:05 |
Opening Speech by Shanghai Plastic Industry Association |
|
|
09:15 |
Comprehensive Solutions of Innovative Materials in Industrial Products |
|
|
09:50 |
Material Innovation Promote the Design of Industrial Products |
|
|
10:25 |
Coffee Break + Exhibition Visit |
|
|
11:10 |
Study of Global Rubber& Plastics and Innovative Materials Mr. Sean Xiao, A&T Industry Research Managerat Frost & Sullivan China |
|
|
11:45 |
Group Photo |
|
|
12:00 |
Luncheon |
|
|
P.M. |
SessionⅠ.Automotive Interiors and Exteriors |
SessionⅡ.Engine and its Surrounding Parts |
|
13:30 |
Quick Self-Introduction |
Quick Self-Introduction |
|
13:45 |
The Present Situation and Development Trend of Automobile and Parts Industry in China Distinguished Advisor China Association of Automobile Manufacturers |
The Trends of Plastic on the Engine
Intake & Exhaust Design engineer, Pan Asia Technical Automotive center Co.,Ltd |
|
14:20 |
The Innovation Solutions of Measuring Mixing Techniques
|
Radici Engineering Plastic: A Key Partner in Auto Market
Mr. Xu Xiaodong Market Development Manager RadiciGroup |
|
14:55 |
Optimize application of Moldflow Simulation Technology in Automotive Mr. Huang Mingzhong Technical Manager Autodesk, Inc. |
The Application of Thermal Analysis in Composite Materials Mr. Pengfei Kong, Thermal Analysis Technology Consultant METTLER TOLEDO |
|
15:30 |
Coffee Break + Exhibition Visit |
|
|
16:15 |
Energy-saving, Environmental Material in Improving Vehicle Air Quality Senior Manager SAIC Motor Corporation Limited Passenger Vehicle Co., |
The Development Trend of Materials Technology Of Car Engine
Former Vice General Technologist Dongfeng Electronic Technology Company |
|
16:50 |
VOC solution of interior design and manufacture Manager of Polymer Material Development Room Changchun FAWAY-Johnson Controls Automotive systems CO., LTD. |
The Lightweight Solution Of Engine and its Surrounding Parts Manager of Non-metal Materials Chery Auto |
|
17:30 |
Cocktail Party |
|
|
Day 2 Mar.13th(Fri） |
||
|
A.M. |
Keynote Speech |
|
|
09:00 |
Causes and Solutions of Injection Molding Plastic Part Warpage and Crack Mr.Charles Hsu, SAMT Founding Director,Society of Advanced Molding Technology (SAMT), Hong Kong |
|
|
09:35 |
Innovative Solutions by Demag Injection Molding Machine DemagPlasticsGroup |
|
|
10:10 |
Coffee Break + Exhibition Visit |
|
|
A.M. |
Keynote Speech |
|
|
11:10 |
The SUV Lightweight Car Body Design Method and Application Mr. Lei Shi, Technical Director, R&D of Great Wall Motor |
|
|
11:45 |
The Innovation Technology of The Domestic Electric Vehicles and Lightweight Materials Mr. Ruilin Tang, Deputy Chief Engineer, Shanghai Haima Automobile R&D Co.,Ltd |
|
|
12:20 |
Luncheon |
|
|
P.M. |
Round Table Discussion |
|
|
13:30 |
The Latest Application Trend of theAutomotive Plastic -Material Selection, Forming Technology, Performance, Application of the Innovation Application Cases |
|
|
14:40 |
Coffee Break + Exhibition Visit |
|
|
15:40 |
Lucky Draw |
|
Package Plan
eve Conference Detail Testimonial
Focus on automotive materials, focusing on the automotive industry, and wish the conference even better!
——Mr. Zhijun Peng, Trim Section Supervisor at ANHUI JIANGHUAI AUTOMOBILE CO.,LTD. TECHNICAL CENTER
Thanks to Ringier who gave this such wonderful seminar!
——Mr. Gaoyong Li, Material Engineer at Delphi Electrical/Electronic Architecture
The meeting content is rich, very fascinating!
——Mr. Bruce Huang, CAE Manager at Ningbo Changhua Auto Products Co., Ltd.
